Every truck, measured. No stops. No spreadsheets.
An overhead LiDAR gantry at the mine gate. Trucks drive through at haul-road speed. Volume, tonnage and truck ID land in your system before the truck reaches the weighbridge queue, which you probably don't need anymore.
Four ways your payload data is wrong today.
The weighbridge is a single number arriving at a single point. It tells you what the truck weighed at the bridge, not what left the loader, not what stayed stuck in the bed, not whether the load was centred. The difference shows up in trucking factor, in tyre wear, and in quarterly reconciliation meetings nobody enjoys.
Volume guesses, not measurements.
Operators fill by eye. Revenue leaks both ways, under on capacity, over on tyre wear and fuel.
Sticky residue inflates empty-bed baselines.
Every cycle drifts. Tonnage accuracy erodes quietly until someone runs the numbers at quarter close.
Suspensions wear. Spillage builds up.
Bias in load distribution costs maintenance budgets and hauls material onto haul roads. Invisible to a bridge.
Reconciliation isn't a control point.
Losses between loading and weighbridge are attributed to "shrinkage" because nothing else can describe them.
Scan. Analyse. Act.
A continuous measurement pipeline built into the haul road, not another system your team has to log into.
Truck passes under the gantry.
LiDAR builds a volumetric point cloud of the loaded bed. Stereo cameras capture imagery. ANPR reads the number plate; RFID takes over in dusty conditions.
Volume to tonnage. Automatically.
Point cloud becomes volume. Material density converts to tonnage. Empty-bed profile compared against loaded to isolate carryback. Results are in your ERP within seconds.
Shift-level trends. Exception alerts.
Dashboards per route, loader, operator and shift. Alerts when loads drift outside tolerance. Timestamped photo audit trail for every trip, exportable.
Industrial hardware. Edge-native software.
Built on mechanical LiDAR, chosen over solid-state for its wider field of view and faster refresh rate at mine-haul speeds.
Versus weighbridges and imported scanners.
| Capability | Weighbridge | Imported scanner | MineVision |
|---|---|---|---|
| Measurement type | Static weight | Volumetric LiDAR | LiDAR + stereo imaging |
| Throughput impact | Stops required | Drive-through | Drive-through, 10-15 km/h |
| Carryback detection | No | Partial | Yes, empty vs loaded profile |
| Indian procurement fit | Low | Forex · long lead times | Make in India · tender-ready |
| Support timezone | Local vendor | Eight time zones away | Hyderabad + Jharkhand |
What are the losses costing you?
A first-pass estimate of annual recovery with continuous payload measurement. Pilot data makes these numbers more precise.
Tender-eligible. Documentation-ready.
Indigenous product, in-country support, and the compliance trail your procurement and compliance teams need, packaged at engagement, not requested afterwards.
Origin & compliance
Indigenous hardware, firmware, AI models and integration layer. Full origin documentation available on engagement.
Tender pack
Technical specifications, compliance statements, reference deployment summaries and commercial terms in the formats Indian mining tenders expect.
Warranty & SLA
Standard on-site warranty, SLA-backed uptime commitments, and scheduled maintenance contracts available as part of the deployment package.
Reference visits
Operational pilot site in Jharkhand available for site visits, including sensor demonstrations and parallel-weighbridge accuracy review.
Pilot in months. Scale in quarters.
A phased rollout that protects uptime and proves value before scale.
Site survey & mounting design
Site visit covering dust levels, truck mix, entry/exit geometry, power and network. You receive a formal technical report of the kind state mining authorities routinely request.
Installation & calibration
Gantry fabrication and installation (2-3 days on site). Power, network, calibration. Parallel operation with existing weighbridge for accuracy verification.
Pilot operation & reporting
One quarter of live operations. Daily shift reports, weekly accuracy reconciliation, monthly ROI tracking against baseline. All data owned by you.
Integration & scale
Full integration with your mine ERP. Operator training, go-live support. Additional modules (conveyor, mapping) added based on pilot outcomes.
Frequently asked.
Does it slow down truck throughput?
What installation is required?
How accurate is it in real mining conditions?
Can it detect carryback?
How does it handle dust and monsoon conditions?
How does it integrate with existing mine management systems?
What if the number plate is obstructed by dust?
Is this product Make in India compliant?
Run it for a quarter. Read the numbers.
See the difference in your trucking factors, with data you can audit.